REM T3b for the Black Ring Sight now available

[M1P90]

REM T3b
The Reticule Enhancement Module (T-bar) 3 (black ring sight)

[size=6]The price is $89.00 shipped.

I take checks, Money Orders or I can do Pay Pal. My Pay Pal acct. is croenker@verizon.net

Or go to http://www.m1bullpup.com to pay buy Visa, Mastercard, or Discover

PM me or e-mail me at croenker@verizon.net
Include your full name and address and LED color choice so I can put you on the order list.

The Reticule Enhancement Module (T-bar) 3b is to be used as a back up to the Black Ring Sight. Try to rely on the Black Crosshairs when possible.

The Reticule Enhancement Module 3b (REM T3b) fixes the problem that is inherent in the Black Ring Sight. We all know in certain low light conditions the Ring Sight looses its sight picture. When that happens just turn on the REM T3b and you will get a sharp T bar sight picture.

The REM T3b Illuminates the T bar via a colored LED (red or green or blue) that is attached to the underside of the Ring Sight. There needs to be minor drilling and gluing to affix the T3b to the Sight.

It has 11 illumination settings so the T bar can be seen outdoors in daylight (on its brightest setting) or in total darkness (on its lowest setting). The REM T3b fits in the sling well just under the Ring Sight. It is ambidextrous so it can be mounted on the left or right side of the rifle.

The REM T3b uses one CR2032 3 volt battery. The battery life is 106 hours of continuous use.

Since we did not make the Rheostats...
The REM T3b has a 1 YEAR Warranty. I will replace it if it fails due to a manufacturing problem. (I will have to examine it first to make sure there wasn't some other factor that caused the failure). You just pay for the shipping ($5.00). If after 1 year a manufacturing problem should occur... contact me and I will see what I can do for you.

The REM T3 comes with a 30 day money back guarantee. If you are dissatisfied with it, please send it back to me and I will give you a full refund. (You just pay the shipping)


The electrical wire will have a metal wire in it so it can be positioned out of your line of sight.

Standard view of the USG on a cloudy day.



Same view with the REM T3b turned on high.



Standard view of the USG against a black target. (Can't see a thing)



Same view with the REM T3b turned on high. (I can see!)


Same view with the REM T3b turned on high (green LED).


Same view with the REM T3b turned on high (blue LED).



USG sight in normal mode.



USG sight with the REM T3b set on #1 (red LED)


USG sight with the REM T3b set on #1 (green LED)


USG sight with the REM T3b set on #1 (blue LED)

[SONYtec]

Any pictures? How are you able to get that done?

[M1P90]

Any pictures? How are you able to get that done?

Just posted a few pics.

To get this done I have to go underneath the ring sight. I found that the USG sight DOES have a tritium bar in the same place as the white ring sight. It is covered by a black rubber coating. I have to cut a hole to expose a portion of the Tritium bar, being careful not to go too deep or the lense could be scratched. I install my form fitted LED and epoxy it in place.

[SONYtec]

Very nice! Now I wish I had bought the black ring sight version.

Gotta be some way you can light up the ring part of the sight.

[M1P90]

PROCESS TO ATTACH THE REM T3b TO THE BLACK RETICLE SIGHT

The black reticle sight needs the LED to be permanently attached to the underside.

There needs to be a minor operation on the USG sight in order to expose the tritium bar and to attach the LED. Make sure you don't cut too deep or you may damage the glass optic.
I'll do the procedure at no extra cost.


You will need a Dremel and use this 3mm tool to drill a hole in the rubber Tritium cover.


You will also need an exacto knife to finish cleaning out the hole to expose the Tritium.


NOW THE FUN STARTS.

1) Cut a small hole the size of the LED and expose the Tritium bar. Be careful not to drill the Tritium. (drill slowly)


2)Make sure the hole is centered.




3) Finish removing debris from hole by cutting the rubber and pulling it out with tweezers.


4) Picture of completed hole.


5) Use 5 minute epoxy to attach T3b to Ring Sight


6) Immobilize the T3b to the Ring Sight and insert the LED into the hole.
Hold it in place with the tip of the exacto knife.


7) While holding the LED in place, Cover the LED and rubber area and part of the metal with the 5 minute epoxy. You will have to hold the LED for 10 to 15 minutes.


After 10 to 15 minutes pull out the knife and then use the back flat part of the knife to hold the LED in place untill the epoxy solidifies. (another 5 munites)


9) Completed process.


10) Carefully bend the LED wire to the side of the Ring Sight you desire.


11) Attach the REM T3b to the rifle and re-attach your Ring Sight.
ALL DONE!!



You can now see the cross hairs in any light condition and against any background.

Video part 1
http://www.youtube.com/watch?v=c5-ha92_YJY

Video part 2
http://www.youtube.com/watch?v=knc1zetc8z8&NR=1

Video part 3
http://www.youtube.com/watch?v=ch63jXMYvgI&NR=1

Video part 4
http://www.youtube.com/watch?v=6wK8MG4OG3w&NR=1

Video part 5
http://www.youtube.com/watch?v=HMdQHnSdbzo&NR=1

[SONYtec]

Nice job M1P90 !!!

[Merlin]

I had Chris install mine (T3B) and everything is as advertised. Great idea and product.

[M1P90]

REM T3b Instruction Manual


Thank you for purchasing this upgrade to your PS90 Ring Sight. The REM T3b was designed to maximize your shooting pleasure by fixing the deficiencies of the Ring Sight.



Installation
1) Carefully bend the LED wire
to the side of the Ring Sight you prefer.
2) Place the dialed rheostat on one side of the Sling Well and the small holder on the other side. Tighten the mounting screws until both sides are secure. Use the Allen wrench that is supplied for this procedure. (DO NOT OVER-TIGHTEN) to prevent damage to the screw pins. You can use BLUE thread locker if you like but it is not necessary.
3) Re-attach your Ring Sight to the PS90.




You can now turn on and use the REM T3b.


NOTE: The REM T3b does not interfere with the Tritium Bar so in total darkness you can still rely on that as a light source if desired.

NOTE: When using the REM T3b in total darkness, with no tactical lights in use, you may notice a slight glow on the front optic glass within short distances (less than 10 feet.) This does not interfere with use of the REM T3b.

Battery Replacement
Hold the “numbered part” of the Rheostat so it doesn’t turn. Turn the outside Rheostat battery cover counter clockwise to remove cover. The REM T3b uses one Lithium 3volt CR2032 battery. This package contains ONE spare battery for your convenience.

Warranty
This Product is warranted against original defects in material and/or manufacturing for one year. This warranty is void if the unit has been abused, disassembled, or modified/tampered with in any way from its original configuration.

This warranty does not apply to defects caused by normal wear and tear, improper handling, incorrect installation, accidents, and alterations/modifications to the original configuration, repairs made by unauthorized parties, aftermarket accessories, or abnormal use.

Contact Us
We hope you find the REM T3b to be a great enhancement. We invite your comments. If you have any questions, concerns or comments, please contact us at 978-852-8584 or croenker@verizon.net.

Visit my web site at:
http://www.M1Bullpup.com

[M1P90]

FYI

The REM T3b is now available for sale and is in stock!

Come and get em!

[ink]

so is this only for use with the black ring sight version or does it work just as well on the white ring sight version as well?